Neutral

To effectively implement Permeable Rock Dam practices, the following steps should be carried out:

• Step 1: Consider constructing a permeable rock dam across relatively wide and shallow valleys.
• Step 2: Permeable rock dams should consist of long, low rock walls with level crest along full length although farmers should consider central spillways where water course has cracks.
• Step 3: The dam should be between 50-300m in length and 1m in height within a gully.
• Step 4: Consider making the dam wall flatter on the downslope side than on the upslope side.
• Step 5: A foundation of small stones should be set in the trench.
• Step 6: An apron of large rocks is essential to split the erosive force of the overflow.
• Step 7: Downstream banks of the water stream should be shielded by stone pitching to prohibit the increase of the gully.

To effectively Water Spreading Bunds the following should be carried out:

• Step 1: Farmers should consider making earth bunds by hand, animal ploughs or mechanised ploughs.
• Step 2: Contour bunds:
  • Contour lines must be plotted and marked prior to developing the bund.
  • A 40 cm deep infiltration pit is dug directly above where the bund will be plotted.
  • Bunds should be spread 5 m to 10 m apart.
  • Material from the infiltration pit will be piled and compacted to form a 25 cm to 30 cm in height with a base of 75 cm.
  • Soil is piled to form a ridge along the contour. The more significant the slope, the closer the bunds must be plotted.
• Step 3: Semi-circle bunds:
  • Contour lines must be plotted and marked prior to developing the bund.
  • A centre point is chosen as diameter for the bund is selected (this could be 3 m or 30 m depending on the available space). From the centre point a string is used to stake out an even semi-circle.
  • Excavate a small trench before the bund and pile the excavated material. Pile and compact a bund wall, wetting it often to form the wall.
• Step 4: Contour stone bunds:
  • Developed on less steep slopes.
  • Must have access to local stones.
  • Dig out a shallow ditch, 10 cm to 15 cm in depth.
  • Lay largest stones at the bottom of the ditch and pile smaller stone upward.
  • Step 5: Regular monitoring of bunds should take place, especially after rain events or after significant periods of time. Repairs should be done if any damage is found.

To effectively implement Half-moon techniques, the following steps should be carried out:

• Step 1: Farmers should consider the diameter of the half-moon  between 2 m – 3 m, with a total surface area of approximately 1.5 sqm and 3.5 sqm.
• Step 2: Pits should be dug to a depth of between 15 cm to 30 cm.
• Step 3: Excavated material can be piled around the curved section of the half-moon.
• Step 4: The curved section of the half-moon can be reinforced by stones to prevent washouts of the half-moon.
• Step 5: 35 kg of organic fertilisers/compost should be evenly distributed in the half-moon.

To effectively In Field Water Harvesting techniques, the following steps should be carried out:

• Step 1: Land is cleared, berms are developed, and crops are planted in order to direct water to the infiltration point.
• Step 2: The catchment areas should be sloped no more than 5 % and the area should be cleared to promote catchment as much as possible.
• Step 3: The infiltration pit (where water is stored) should be dug at the lowest point of the catchment areas and line infiltration pits with plastic or concrete roofing to limit water loss, and can be used as a source of irrigation for fruit trees and other high value crops.
• Step 4: Paths can be built of soil to guide water to the infiltration pit.
• Step 5: Alley cropping, or strop cropping can be used, with areas between trees and crops dug deeper like a trough to direct water to the infiltration pit.
• Step 6: To access water from infiltration pits, farmers can introduce a pumping system and water can be distributed around the farm as necessary

To effectively implement drip irrigation:

• Step 1: A reliable water source must be available - natural (natural or through rain-water harvesting).
• Step 2: Acquire a pump system (approximately $US 100) that maintains enough pressure to deliver water through the system or an elevated tank.
• Step 3: Connect lines or hoses and laterals that run from the pump system across the planted fields.
• Step 4: Run lines or hoses with emitters (drippers) or small punctures at the surface level along planted crops or just below the surface providing water to the roots system of the plants.
• Step 5: Once the system is operable, the pump can be turned on and water dispersed as required by the nature of the crop and can also be implemented with supplemental irrigation strategies (Technical Brief 23).
• Step 6: Monitor the irrigation system regularly to ensure there are no malfunctions and the system is maintained. Crops that receive regular water can develop shallow root systems and any prolonged disruptions in service could have   significant impacts.
• Step 7: If applying drip irrigation in sloped conditions, follow the contours of the slope as outlined in Technical Brief 16.

Once a drip irrigation system is up and running, farmers can explore fertigation, the addition of soluble fertilisers into the irrigation system water for distribution directly to plants.

To effectively undertake seed saving:

• Step 1: Communicate with national agricultural extension and local farmers regarding seed harvesting timing and practices for local crop species.
• Step 2: Clear field and sow desired crop using climate smart agriculture practices.
• Step 3: Monitor plant life cycle and ensure that seeds are extracted correctly and are not spoiled in the process. Employ local expertise to ensure seed harvesting is carried out correctly.
• Step 4: Post-harvest, seeds should be adequately dried and then transferred to proper storage facilities.
• Step 5: store seeds in dry, cool, and dark locations. This will prevent them from spoil. Different strategies for seed storage are implemented around the region so local expertise should be sought.
• Step 6: Ensure that pests are excluded from storage areas to prevent loss or spoil (Technical Brief 61-65).
• Step 7: Community seed banks or seed trading should be established to allow farmers to integrate different varieties into their farming system that are resilient to local climatic conditions

To effectively undertake weed control measures:

• Step 1: Review weed control measures - crop rotation, intercropping, cover crops, mulching, seed-bed preparation, livestock grazing, seed/variety selection, mowing, hand-weeding and adjustments to tillage practices - and determine which methods are available and appropriate for the farming system and farmer. Two or more of these techniques can be applied to assist in ensuring farmers have more chance of success. Understand possible negative impacts of each weed control method.
• Step 2: Improve weed identification knowledge in specific areas.
• Step 3: Prevent weeds from spreading – clean clothes, animals, machinery, vehicles to limit weed transport; use only well stored/rotted manure (4-5 months) (Knowledge Product 16), include fencing, irrigation and other farm ‘breaks’ where possible
• Step 4: Apply a combination of weed control methods including – cover crops (Technical Brief 15), mulching, intercropping (Technical Brief 07), crop rotation (Technical Brief 09), livestock grazing, seed selection (Technical Brief 20), mowing, hand-weeding. Try to avoid the application of herbicides, tillage and burning.
• Step 5: monitor and document most effective weed management strategies for each farmer, and use lessons learned from the area with other farmers where applicable.

While agroforestry practices are deemed highly beneficial and climate smart, it is important to ensure that proposed practices are appropriate for the specific context – the benefits of the agroforestry practice match the needs of the farmer - and are fit for purpose. Obtain advice from an agroforestry expert before embarking on secondary crop/hedge species selection.

To effectively implement alley-cropping the following should be carried out:

• Step 1: Clearly understand the objectives of the intervention and identify an appropriate species for intercropping. For maize and sorghum in a smaller subsistence farm setting, selection and growth of hedge rows of a legumes such as cowpea or Gliricidia can provide sustainable benefits in terms of soil quality and secondary fodder/food products. In larger fields, timber trees can be planted every five to ten crop rows, depending on the height of the mature tree, and the shade-tolerance of the crop.
• Step 2: Identify and understand key conditions, such as prevailing wind direction, and sunlight to ensure that the field is planted in an appropriate configuration, with primary crop and secondary (hedge/shrub/tree) crops planted in such a way as to benefit the primary crop and not compete with it. East to west row orientation should maxmise sunlight, topography permitting.
• Step 3: For beneficial hedgerow growth with legume species such as Leucaena, cliricidia, and Sesbania sesban, the trees should be planted in rows between two and four metres apart, with individual trees planted as close as possible - between 10 to 15 cm apart. If planted closely, the trees will favour leaves over step growth, creating more mulch to prune for cover. Note that if rows are planted too closely, the secondary crop can dominate the available crop land reducing productivity. Furthermore, the closer the hedges, the more shade will present, which can depress crop growth, and also start to compete for soil water and nutrients, which is not beneficial.
• Step 4: Once reaching sufficient maturity, after approximately six months (one-metre tall for legumes)– hedges should be pruned to generate mulch for working into the soil. Then the primary crop (maize) can be planted. Pruning once per month thereafter provides cover and ensures that light penetration is maintained. Planting legumes approximately six months before planting the primary crop can ensure that sufficient pruned material is available to incorporate into the soil to enhance growth.
• Step 5: After harvesting the primary crop, hedgerows can be left to grow taller so that shade reduces weed grown, and to develop material to prune and incorporate into the soil again during the following crop cycle. However, hedges should not be allow to grow too high or dense as their roots will dominate the soil and out-compete primary crops for water and nutrients.

Before implementing any of these technologies, further research may be required beyond the guidance provided here. The World Agroforestry Centre (ICRAF) has many resources, toolkits and success stories that can support such research.

To effectively implement cover crops:

• Step 1:  Research whether locally available crops (especially legumes) provide potential options for cover crops.
• Step 2: Establish a demonstration plot could provide farmers with an example of how cover crops function.
• Step 3: Plant cover crops between primary crop growing systems to improve soil fertility, quality and nutrients.
• Step 4: Monitor soil structure, nutrient levels, and field integrity to ensure efficacy.
• Step 5: Incorporate cover crops with other climate smart practices enhance soil, including: Intercropping (Technical Brief 07), Crop Rotations (Technical Brief 09) Reduced/No-tillage Options (Technical Brief 12) etc

To effectively undertake trash lines:

• Step 1: Collect straw, stalks, picked weed or other organic materials from field or surrounding area.
• Step 2: Establish contour lines using method identified in contour planting (Technical Brief 16).
• Step 3: Contour lines for trash lines should be spaced between 5 to 10 m apart.
• Step 4: Heap straw along contour lines on hilly or sloped fields to be approximately 0.5 m wide and up to 0.3 m in height.
• Step 5: Trash should be piled on annually or as the field is prepared. Lines can be maintained for a few years and then decomposed materials can be mixed into the soil.