High

To effectively implement assisted reproduction using artificial insemination:

• Step 1: A qualified veterinarian or service provider should be readily available and preferably contracted to carry out the procedure as they should have the necessary training, instruments and facilities to carry out procedures;
• Step 2: The farmer should suggest the type of breed for his animal, and the veterinarian should advise the farmer on the feasible breed for the cow.
• Step 3: The farmer has to identify the cow on heat by observing the heat signs (uneasiness, making loud unusual noise, mounting others, standing when mounted, producing mucus discharge from the vulva, etc.)
• Step 4: The identified animal is isolated from the rest of the animals.
• Step 5: Communicate with the veterinarian or trained service provider to carry out the procedure by determining the readiness of the cow to undergo the AI service (stage of heat cycle). Early reporting increasing chances of successful conception.
• Step 6: The veterinarian or service provider then carries out the procedure to the cow after confirming readiness of the animal.

To effectively implement Permeable Rock Dam practices, the following steps should be carried out:

• Step 1: Consider constructing a permeable rock dam across relatively wide and shallow valleys.
• Step 2: Permeable rock dams should consist of long, low rock walls with level crest along full length although farmers should consider central spillways where water course has cracks.
• Step 3: The dam should be between 50-300m in length and 1m in height within a gully.
• Step 4: Consider making the dam wall flatter on the downslope side than on the upslope side.
• Step 5: A foundation of small stones should be set in the trench.
• Step 6: An apron of large rocks is essential to split the erosive force of the overflow.
• Step 7: Downstream banks of the water stream should be shielded by stone pitching to prohibit the increase of the gully.

To effectively implement solar irrigation:

• Step 1: To determine the solar pump system Crop water requirements, location, water sources etc. Do required research. Is water sourced from an above ground or below ground source?
• Step 2: Source required materials to implement a solar irrigation system from regional or international suppliers including:
  • Photovoltaic (PV) panels to generate electricity (80-300 W system depending on context);
  • a structure to mount the panels;
  • a pump controller;
  • a surface or submersible water pump; and
  • a distribution system or storage tank for water.
• Step 3: Identify funding sources as initial costs, as well as maintenance costs, must be considered and modelled prior to purchasing a system. There are regional and international solar irrigation producers.   These costs differ dramatically given the complexity of the context, starting at costs approximately USD $2,400 for equipment only. If drilling is necessary the cost increases significantly depending on depth, substrate etc.  Community-based investment, micro-leasing and rental services can be possible funding models to explore.
• Step 4: Determine whether there is sufficient solar irradiation for the proposed area – consult and specialist; and/or the national meteorological service.
• Step 5: Identify area suitable to install solar panels. The area should be easily accessible, and all trees/bush should be cleared. To determine most appropriate site and angle of panels, etc, consult an expert.
• Step 6: The availability of technical expertise must be considered before implementation to ensure that any technical issues do not result in long period of service disruption.

Maintenance costs and expertise should be considered before installing solar irrigation systems. A detailed cost benefit analysis is advisable. Other key technical considerations include: Legal permits to extract water from the source as water extraction may impact community watershed levels.

To effectively approach to terracing construction:

• Step 1: Measure slope angle – should not exceed 25 degrees and soils should be at least 0.5 metres deep.
• Step 2: Plot the contours – see Technical Brief 16 Contour Planting for instructions for staking-out contours, and the diagram below for use of a t-stick to measure the distance between contours.
• Step 3: Start at the lowest terrace. Dig a trench vertically below the next contour, and then dig outwards to the lowest contour. Remove soil and place downhill below the lowest contour.
• Step 4: Compact soil on constructed terrace.
• Step 5: Work should then progress upslope, emptying top-soil on to the terrace below to provide soil for planting.
• Step 6: Strengthen riser buttress walls (back-walls) with stones, compacted soil, or by planting grass or trees.
• Step 7: Terrace-end drainage should also be considered, so water does not pool too heavily. The down-field gutters can be lined with stones to reduce erosion

Detailed diagrams and tables for calculating terrace dimensions are provided in Peace Corps 1986, Soil conservation techniques for hillside farming.

Additional guidance can be sought from videos provided by Access Agriculture: SLM02 Fanya Juu terraces. The Kenyan example provided is also up-slope terrace construction but using a different method where a trench is dug, and the loose topsoil is thrown up-hill (fanya juu in Kiswahili) which forms a ridge that flattens over time.