5 to 10ha

To effectively implement Zai Pits the following should be carried out:

• Step 1: Zai pits should be dug with a diameter of 30 cm to 40 cm and 10 cm to 15 cm deep. 
• Step 2: Pits should be spaced 70 cm to 80 cm apart resulting in approximately 10,000 pits per hectare.
• Step 3: The farmer should place 2 – 3 handfuls (200 g to 600 g) of organic fertilisers or compost in each pit.
• Step 4: Holes that are dug between planting seasons will trap wind eroded soils, which are fertile and form good soils for plating crops.
• Step 5: It is recommended that 3 tonnes of fertiliser/compost per hectare be available.
• Step 6: Farmers should consider planting crops in these pits prior to periods of rain.
• Step 7: Repeated application of Zai pit technology on an annual basis will increase productivity of degraded land in the long term.

To effectively implement drip irrigation:

• Step 1: A reliable water source must be available - natural (natural or through rain-water harvesting).
• Step 2: Acquire a pump system (approximately $US 100) that maintains enough pressure to deliver water through the system or an elevated tank.
• Step 3: Connect lines or hoses and laterals that run from the pump system across the planted fields.
• Step 4: Run lines or hoses with emitters (drippers) or small punctures at the surface level along planted crops or just below the surface providing water to the roots system of the plants.
• Step 5: Once the system is operable, the pump can be turned on and water dispersed as required by the nature of the crop and can also be implemented with supplemental irrigation strategies (Technical Brief 23).
• Step 6: Monitor the irrigation system regularly to ensure there are no malfunctions and the system is maintained. Crops that receive regular water can develop shallow root systems and any prolonged disruptions in service could have   significant impacts.
• Step 7: If applying drip irrigation in sloped conditions, follow the contours of the slope as outlined in Technical Brief 16.

Once a drip irrigation system is up and running, farmers can explore fertigation, the addition of soluble fertilisers into the irrigation system water for distribution directly to plants.

To effectively undertake deficit irrigation:

• Step 1: Determine critical growth cycle of desired crops.
• Step 2: Experiment with SI strategies to determine critical watering times prior to upscaling.
• Step 3: Strict management is required to determine the level of transpiration deficiency allowable without significant reduction in crop yields.
• Step 4: Farmers capable of implementing deficit irrigation must have access to the minimum required water to implement deficit irrigation.
• Step 5: Farmers must have access to a reliable water source, irrigation systems, including water distribution system, sprinklers and/or drip irrigation system.

To effectively implement solar irrigation:

• Step 1: To determine the solar pump system Crop water requirements, location, water sources etc. Do required research. Is water sourced from an above ground or below ground source?
• Step 2: Source required materials to implement a solar irrigation system from regional or international suppliers including:
  • Photovoltaic (PV) panels to generate electricity (80-300 W system depending on context);
  • a structure to mount the panels;
  • a pump controller;
  • a surface or submersible water pump; and
  • a distribution system or storage tank for water.
• Step 3: Identify funding sources as initial costs, as well as maintenance costs, must be considered and modelled prior to purchasing a system. There are regional and international solar irrigation producers.   These costs differ dramatically given the complexity of the context, starting at costs approximately USD $2,400 for equipment only. If drilling is necessary the cost increases significantly depending on depth, substrate etc.  Community-based investment, micro-leasing and rental services can be possible funding models to explore.
• Step 4: Determine whether there is sufficient solar irradiation for the proposed area – consult and specialist; and/or the national meteorological service.
• Step 5: Identify area suitable to install solar panels. The area should be easily accessible, and all trees/bush should be cleared. To determine most appropriate site and angle of panels, etc, consult an expert.
• Step 6: The availability of technical expertise must be considered before implementation to ensure that any technical issues do not result in long period of service disruption.

Maintenance costs and expertise should be considered before installing solar irrigation systems. A detailed cost benefit analysis is advisable. Other key technical considerations include: Legal permits to extract water from the source as water extraction may impact community watershed levels.

To effectively undertake leverage traditional seed characteristics, or improved crop varieties  the following should be carried out:

• Step 1: Prior to selecting seed varieties, perform a Cost Benefit Analysis (CBA) to identify how crops will perform and their benefits compared to the costs of the seed, considering the following:
  • Local  farming system(s): land availability per household, crops traditionally grown, access to inputs such as fertilisers,
  • Local environmental conditions: soil conditions, disease, pests, climatic conditions, occurrence of flooding/droughts and other natural disasters.
  • How climate change has impacted or will impact the farming system and how crop variety selection can be a climate- smart practice.
  • Local access to seeds – is seed collected at the householder level, do neighbours exchange seeds, do farmers have access to commercially produced seeds?  Are the costs for accessing commercial, improved seeds manageable or prohibitive? The CBA should weigh the benefits of a new seed against perceived actual or transactional costs for selecting a new seed.
• Step 2: Obtain information and guidance from local experts, lead farmers, and government regarding best varieties to grow.
• Step 3: Evaluate results of the CBA and select appropriate seeds that match the farm system/requirements, and available financial resources/access to credit.
• Step 4: Plant test plots of selected seeds to understand if benefits are realised and demonstrate outcomes with farmers, showing possible alternatives and discuss implementation.
• Step 5: Following full demonstration and discussion with farmers, implement at farm level – planting the first crop in accordance with guidance provided by seed provider, or traditional knowledge.

Consider in-country seed sources to access different varieties through local extension or research services. When buying seeds ensure that the seeds are adequately dry and look for seed that is certified by a national seed laboratory to ensure that the variety is the highest quality possible. Seeds should be properly stored to avoid high temperatures and humid air to reduce chances of early germination.

To effectively undertake weed control measures:

• Step 1: Review weed control measures - crop rotation, intercropping, cover crops, mulching, seed-bed preparation, livestock grazing, seed/variety selection, mowing, hand-weeding and adjustments to tillage practices - and determine which methods are available and appropriate for the farming system and farmer. Two or more of these techniques can be applied to assist in ensuring farmers have more chance of success. Understand possible negative impacts of each weed control method.
• Step 2: Improve weed identification knowledge in specific areas.
• Step 3: Prevent weeds from spreading – clean clothes, animals, machinery, vehicles to limit weed transport; use only well stored/rotted manure (4-5 months) (Knowledge Product 16), include fencing, irrigation and other farm ‘breaks’ where possible
• Step 4: Apply a combination of weed control methods including – cover crops (Technical Brief 15), mulching, intercropping (Technical Brief 07), crop rotation (Technical Brief 09), livestock grazing, seed selection (Technical Brief 20), mowing, hand-weeding. Try to avoid the application of herbicides, tillage and burning.
• Step 5: monitor and document most effective weed management strategies for each farmer, and use lessons learned from the area with other farmers where applicable.

To effectively approach to terracing construction:

• Step 1: Measure slope angle – should not exceed 25 degrees and soils should be at least 0.5 metres deep.
• Step 2: Plot the contours – see Technical Brief 16 Contour Planting for instructions for staking-out contours, and the diagram below for use of a t-stick to measure the distance between contours.
• Step 3: Start at the lowest terrace. Dig a trench vertically below the next contour, and then dig outwards to the lowest contour. Remove soil and place downhill below the lowest contour.
• Step 4: Compact soil on constructed terrace.
• Step 5: Work should then progress upslope, emptying top-soil on to the terrace below to provide soil for planting.
• Step 6: Strengthen riser buttress walls (back-walls) with stones, compacted soil, or by planting grass or trees.
• Step 7: Terrace-end drainage should also be considered, so water does not pool too heavily. The down-field gutters can be lined with stones to reduce erosion

Detailed diagrams and tables for calculating terrace dimensions are provided in Peace Corps 1986, Soil conservation techniques for hillside farming.

Additional guidance can be sought from videos provided by Access Agriculture: SLM02 Fanya Juu terraces. The Kenyan example provided is also up-slope terrace construction but using a different method where a trench is dug, and the loose topsoil is thrown up-hill (fanya juu in Kiswahili) which forms a ridge that flattens over time.

While agroforestry practices are deemed highly beneficial and climate smart, it is important to ensure that proposed practices are appropriate for the specific context – the benefits of the agroforestry practice match the needs of the farmer - and are fit for purpose. Obtain advice from an agroforestry expert before embarking on secondary crop/hedge species selection.

To effectively implement alley-cropping the following should be carried out:

• Step 1: Clearly understand the objectives of the intervention and identify an appropriate species for intercropping. For maize and sorghum in a smaller subsistence farm setting, selection and growth of hedge rows of a legumes such as cowpea or Gliricidia can provide sustainable benefits in terms of soil quality and secondary fodder/food products. In larger fields, timber trees can be planted every five to ten crop rows, depending on the height of the mature tree, and the shade-tolerance of the crop.
• Step 2: Identify and understand key conditions, such as prevailing wind direction, and sunlight to ensure that the field is planted in an appropriate configuration, with primary crop and secondary (hedge/shrub/tree) crops planted in such a way as to benefit the primary crop and not compete with it. East to west row orientation should maxmise sunlight, topography permitting.
• Step 3: For beneficial hedgerow growth with legume species such as Leucaena, cliricidia, and Sesbania sesban, the trees should be planted in rows between two and four metres apart, with individual trees planted as close as possible - between 10 to 15 cm apart. If planted closely, the trees will favour leaves over step growth, creating more mulch to prune for cover. Note that if rows are planted too closely, the secondary crop can dominate the available crop land reducing productivity. Furthermore, the closer the hedges, the more shade will present, which can depress crop growth, and also start to compete for soil water and nutrients, which is not beneficial.
• Step 4: Once reaching sufficient maturity, after approximately six months (one-metre tall for legumes)– hedges should be pruned to generate mulch for working into the soil. Then the primary crop (maize) can be planted. Pruning once per month thereafter provides cover and ensures that light penetration is maintained. Planting legumes approximately six months before planting the primary crop can ensure that sufficient pruned material is available to incorporate into the soil to enhance growth.
• Step 5: After harvesting the primary crop, hedgerows can be left to grow taller so that shade reduces weed grown, and to develop material to prune and incorporate into the soil again during the following crop cycle. However, hedges should not be allow to grow too high or dense as their roots will dominate the soil and out-compete primary crops for water and nutrients.

Before implementing any of these technologies, further research may be required beyond the guidance provided here. The World Agroforestry Centre (ICRAF) has many resources, toolkits and success stories that can support such research.

To effectively undertake contour planting:

• Step 1: Construct an A-frame that has a plumb-line with a rock hanging down the centre. The base of the A-frame should be 90 cm.
• Step 2: Calibrate the A-frame on flat ground. Ensure that both legs are on the ground. Mark where the plumb line meets the cross bar.
• Step 3: On a slope, working perpendicular to the slope, plant one leg of the A-frame and swing the other leg around until the plumb line meets the mark on the cross bar. Drive a stake into the ground where the first ‘planted’ leg is and continue the process across the slope.
• Step 4: Once the extent of the contour has been staked, tie a string from post-to-post across the slope; this identifies the contour to be planted.
• Step 5: Plant selected crops, develop contour ridges or plant contour strips along the contour line.
• Step 6: Subsequent contours should be spaced 3-5 m up or downhill of the preceding contour line. To determine the length between contour lines, measure off the top of each stake to a stake up or downhill with a tape measure or accurately measured third stick.
• Step 7: Contour ridges can be implemented like Water Spreading Bunds (Technical Brief 28) to form ridges of soil that are formed by tilling or ploughing and can be left after land preparation to further prevent erosive forces. Crops can be planted between these ridges.
• Step 8: The planting of contour strips can be implemented by planting grasses or hedges 20 m (shallow slopes) to 10 m (steeper slopes) apart up or downhill, similar to Trash Lines (Technical Brief 14). This intercropping allows for erosion control and can be used as fodder for livestock.

To effectively implement cover crops:

• Step 1:  Research whether locally available crops (especially legumes) provide potential options for cover crops.
• Step 2: Establish a demonstration plot could provide farmers with an example of how cover crops function.
• Step 3: Plant cover crops between primary crop growing systems to improve soil fertility, quality and nutrients.
• Step 4: Monitor soil structure, nutrient levels, and field integrity to ensure efficacy.
• Step 5: Incorporate cover crops with other climate smart practices enhance soil, including: Intercropping (Technical Brief 07), Crop Rotations (Technical Brief 09) Reduced/No-tillage Options (Technical Brief 12) etc